📍 Dhahran, Eastern Province
Spreader Beam Inspection & Certification in Dhahran
A spreader beam is a below-the-hook device that works in compression, with slings or shackles hanging vertically from each end so the lifting legs do not squeeze long or fragile loads such as pipe, precast units, cabins and modules. It is common in fabrication yards, pipe laydown areas and plant construction in Saudi Arabia, and many are fabricated locally to suit a particular job. A site-built beam without a design basis, weld records or a proof test is a real hazard, so independent inspection and load testing before first use are essential. Headquarters of Saudi Aramco, with a high concentration of contractors operating under Aramco General Instructions.
Spreader Beam inspection in Dhahran: local context
Workshops, laboratories and plant rooms across Dhahran rely on chain blocks, lever hoists, overhead monorails and jacks for routine maintenance, often indoors where a failed hoist can halt wider operations. EES examines and load tests this equipment in place, keeps downtime short and records the result for each individual unit.
Spreader Beam inspection scope in Dhahran
- ✓Main beam for straightness, bowing, dents and local buckling of the web or flanges
- ✓Welds at the lifting lugs, padeyes and end fittings, visually and with MPI or dye penetrant where required
- ✓Padeyes and lifting lugs for hole elongation, wear, cracks, deformation and adequate edge distance
- ✓Adjustable beams: locking pins, pin holes and position markings for the rated configurations
- ✓Shackles and end connections for correct size, pin security and compatibility with the rated load
- ✓Section loss and corrosion, especially inside box sections, and condition of the coating
- ✓Marking of safe working load, self-weight, serial number and permitted sling angles
- ✓Design calculation or drawing, material certificates and previous test records
Defects commonly found
- ✓Cracked welds at padeyes or end plates
- ✓Beam bent or locally dented after an impact or an off-centre pick
- ✓Pin holes elongated or padeyes worn out of tolerance
- ✓Missing or illegible SWL and self-weight marking
- ✓Unauthorised weld repair or modification without re-testing
Standards
- ✓ASME B30.20 (Below-the-Hook Lifting Devices)
- ✓ASME BTH-1 (Design of Below-the-Hook Lifting Devices)
- ✓Manufacturer specifications and load charts
- ✓Saudi Aramco General Instructions (GI), where applicable
Testing
A proof load test is typically carried out at 100%-125% of rated capacity depending on the standard and client, with the beam checked for permanent deformation afterwards and critical welds examined by NDT where required.
Frequency
Typically a thorough examination at least annually, plus an inspection before first use and after any repair, modification or damage, with a visual check before each lift.
Who we support in Dhahran
Local focus areas: Aramco Dhahran, KFUPM and Techno Valley.
Explore more
Category: Hoists & Lifting Tools
FAQs
Can you inspect a spreader beam on site in Dhahran?＋
Yes. Our inspectors travel to your yard or project site in Dhahran, including Aramco Dhahran, KFUPM and Techno Valley, so the equipment does not need to be moved.
Which industries in Dhahran request spreader beam inspection?＋
Typically operators and contractors in the Eastern Province from these sectors: Oil, Gas & Petrochemical.
Does a site-fabricated spreader beam need a design calculation?＋
Yes. A locally built beam should have a design basis that supports its rated capacity, along with material certificates and weld records. Inspectors will normally ask for these before carrying out the proof load test.
What is the difference between a spreader beam and a lifting beam?＋
A spreader beam works mainly in compression and keeps the sling legs vertical, with load hung from each end. A lifting beam works in bending with a lifting point at the centre and loads hung below it, usually to keep the load level.