📍 Yanbu, Madinah Province
Articulating Boom Lift Inspection & Certification in Yanbu
An articulating boom lift uses a jointed main boom and jib to carry workers up and over obstacles such as pipe racks, tanks and structural steel. In Saudi Arabia it is a standard access machine on refinery turnarounds, petrochemical shutdowns and construction sites, where heat, sand and long idle periods accelerate wear on hoses, pins and tyres. An independent inspection confirms that the boom, controls and load-limiting systems perform as the manufacturer intended before a crew is lifted into position. Yanbu Industrial City is a major petrochemical and refining centre on the Red Sea.
Articulating Boom Lift inspection in Yanbu: local context
Process towers, storage tanks and pipe racks across Yanbu Industrial City all need temporary access, so boom lifts, scissor lifts, scaffolding and suspended platforms are widely used during shutdowns. Salt-laden air can corrode platform structures and anchor points, and wind can limit safe use. EES inspects access equipment and checks scaffolding and harness anchorage on site before crews climb.
Articulating Boom Lift inspection scope in Yanbu
- ✓Boom and jib pivot pins, bushings and retaining hardware for wear, free play and missing keepers
- ✓Welds on the turntable, boom sections, riser and platform mounting, with attention to cracks at stress points
- ✓Slew ring and slew drive: bolt tightness, backlash, grease condition and unusual noise during rotation
- ✓Hydraulic cylinders, hoses and fittings for leaks, chafing and heat damage, plus holding-valve performance (no drift with the platform raised)
- ✓Platform load sensing, overload alarm and chassis tilt cut-out, tested from both ground and platform controls
- ✓Ground and platform control functions, emergency stops, emergency lowering and descent alarm
- ✓Axle oscillation lock, steering, brakes and tyres, plus outriggers or axle extension where fitted
- ✓Platform guardrail, entry gate or chain, harness anchorage points and legibility of the capacity and manufacturer plates
Defects commonly found
- ✓Worn boom or jib pivot pins and bushings causing excessive free play at the platform
- ✓Leaking or heat-hardened hydraulic hoses, or cylinders that drift when the boom is raised
- ✓Overload or tilt sensors bypassed, out of calibration or inoperative
- ✓Cracked welds or corrosion at the turntable, riser or jib, particularly on coastal sites
- ✓Missing or illegible capacity and warning decals, and damaged platform gates or harness anchor points
Standards
- ✓ANSI/SAIA A92.20 (design, calculations, safety requirements and test methods for MEWPs)
- ✓ANSI/SAIA A92.22 (safe use of MEWPs)
- ✓ISO 18893 (MEWPs - safety principles, inspection, maintenance and operation)
- ✓Manufacturer specifications and load charts
Testing
A rated-load test is typically carried out, commonly at 100%-125% of rated platform capacity depending on the standard and client, with the boom taken through the positions the manufacturer's working envelope allows. Overload sensing, tilt cut-out and emergency lowering are proven under load.
Frequency
Typically at least annually, with a pre-start check every shift, frequent inspections at manufacturer-defined intervals (often quarterly or by operating hours), and re-inspection before mobilisation where client or site rules require.
Who we support in Yanbu
Local focus areas: Yanbu Industrial City and Yanbu Commercial Port.
FAQs
Can you inspect an articulating boom lift on site in Yanbu?＋
Yes. Our inspectors travel to your yard or project site in Yanbu, including Yanbu Industrial City and Yanbu Commercial Port, so the equipment does not need to be moved.
Which industries in Yanbu request articulating boom lift inspection?＋
Typically operators and contractors in the Madinah Province from these sectors: Vision 2030 Mega-Projects; Oil, Gas & Petrochemical; Power & Utilities.
How often does an articulating boom lift need inspection in Saudi Arabia?＋
Most clients and contractors expect a documented third-party inspection at least annually and before mobilisation to a new site, in addition to the operator's pre-start check each shift. Some client or project rules set shorter validity periods, so confirm the requirement in your contract or site rules.
Does a boom lift need a load test or only a visual inspection?＋
A competent inspection should include a functional test with a rated load on the platform and a check of the overload and tilt systems, not only a visual walk-round. Whether a heavier overload test is needed depends on the standard, the manufacturer and the client.