📍 Ras Tanura, Eastern Province
Scissor Lift Inspection & Certification in Ras Tanura
A scissor lift raises a flat guarded platform vertically on a stack of crossed steel arms, giving workers a large working area and, typically, a higher platform capacity than most boom lifts. In Saudi Arabia electric models are common inside warehouses, malls and plant buildings, while diesel rough-terrain units work on construction sites and yards. Because the machine relies on arm pins, lift cylinders and pothole protection devices to stay stable and controlled, a competent third-party inspection checks them before the unit is released for work. Site of one of the world's largest oil refineries and export terminals, with continuous maintenance and turnaround activity.
Scissor Lift inspection in Ras Tanura: local context
Tall columns, storage tanks, pipe racks and stacks across the refinery and terminal make access equipment a daily need at Ras Tanura, with scaffolds and boom lifts exposed to open coastal wind. EES inspects MEWPs, suspended platforms and scaffolding, checks guardrails and stability, and supports tagging so work at heights can start on time.
Scissor Lift inspection scope in Ras Tanura
- ✓Scissor arm stack: pins, bushings, rollers and wear pads, plus welds at arm pivots and cross-members
- ✓Lift cylinders and holding or lowering valves for leaks, creep and correct manual descent operation
- ✓Pothole protection or slide-out guards deploying and retracting correctly as the platform rises
- ✓Tilt sensor and platform load sensing, including cut-out and alarm when the chassis is out of level or overloaded
- ✓Maintenance support (safety prop) condition and engagement, and the mechanical stops
- ✓Platform guardrails, entry gate or chain, deck extension locks and harness anchor points
- ✓Batteries, charger and wiring on electric units; engine, outriggers and four-wheel drive on rough-terrain units
- ✓Brakes, steering, tyres, travel alarm, descent alarm, horn, emergency stop and emergency lowering
Defects commonly found
- ✓Pothole guards that do not deploy or are bent, so a wheel can drop into a hole with the platform raised
- ✓Worn arm pivot pins, bent or cracked arms and missing wear pads causing platform sway
- ✓Hydraulic leaks from lift cylinders, and lowering valve creep
- ✓Disabled or non-functional tilt alarm and overload sensing
- ✓Damaged or missing guardrail gates and deck extension locks
Standards
- ✓ANSI/SAIA A92.20 (design, calculations, safety requirements and test methods for MEWPs)
- ✓ANSI/SAIA A92.22 (safe use of MEWPs)
- ✓ISO 18893 (MEWPs - safety principles, inspection, maintenance and operation)
- ✓Manufacturer specifications and load charts
Testing
Typically a rated-load test at 100%-125% of platform capacity depending on the standard and client, performed with the platform raised through its travel and, on rough-terrain models, with the outriggers or levelling system in use. Tilt alarm, overload sensing and manual descent are tested alongside.
Frequency
Typically at least annually, with a pre-start check every shift, more frequent inspections where machines are rented and moved between sites, and re-inspection before mobilisation where client or site rules require.
Who we support in Ras Tanura
Local focus areas: Ras Tanura Refinery and Ras Tanura Terminal.
Explore more
Category: Access Platforms & Scaffolding
FAQs
Can you inspect a scissor lift on site in Ras Tanura?＋
Yes. Our inspectors travel to your yard or project site in Ras Tanura, including Ras Tanura Refinery and Ras Tanura Terminal, so the equipment does not need to be moved.
Which industries in Ras Tanura request scissor lift inspection?＋
Typically operators and contractors in the Eastern Province from these sectors: Oil, Gas & Petrochemical.
Is a scissor lift inspection different for electric and diesel models?＋
The structural, hydraulic and safety-device checks are the same, but electric units add battery, charger and motor checks, while diesel rough-terrain units add engine, outrigger and drive checks. The inspector works from the manufacturer's inspection list for the specific model.
Do I need an inspection certificate before a scissor lift can enter a major project site?＋
Most contractors and clients require a current third-party inspection report or certificate, plus evidence of operator competence, before a MEWP is allowed on site. The exact documents and validity period are set by the client's or site's rules.